Assembly pics..

Post your assembly, and/or troubleshooting questions here.

Assembly pics..

Postby Corneleous » Tue Oct 03, 2017 9:15 pm

I will add these pictures to the assembly manual (available from the PRODUCTS page) soon, but for now, here's some pictures, plus commentary from the assembly process. **NOTE** these pictures were taken with a Revision 0 board. Revision 1 is what we're now shipping with the PE6502 kits, and this revision added silkscreened polarity labels to all polarized capacitors. All parts that have a specific orientation are now marked on the PC board using silkscreened labels.

Following the manual, make sure you have all parts ready and organized. Next, clean the PCB with some alcohol and a paper towel.
Image

The first parts to be soldered into place comprise the power supply- an input jack to receive the power adapter, a diode, smoothing capacitors and voltage regulators that provide a stable 5 volts DC, and 3.3 volts DC, and a power LED (and associated resistor). These parts are installed first, so that you can test the power supply voltages after completing this step, without risking any other parts if there is any issue.
Image

Next, install the chip sockets, paying attention to the pin-1 notch on the sockets; All vertical sockets have this notch on top, and all horizontal sockets have the notch to the left side.
Image

The decoupling capacitors, and one additional non-polarized capacitor are installed next. To do this neatly, all of these .1 uF capacitors have 1 leg bent so that the capacitor sort of resembles a capital letter "R". Then they are soldered into place, paying attention to mount the decoupling capacitors as close to the chip as practical.
Image
Image

In the next step, the resistors are installed, and also a resistor pack is installed. This step is a bit of work, but when you're done, there is light at the end of the tunnel!
Image

The PS/2 and the RCA video connector are soldered in next. As with the chip sockets before, and also with the expansion headers later, I use masking tape to hold the parts firmly/fully in place. Once they are soldered, the tape can be removed to reveal a perfectly installed part.
Image

The serial interface is installed next. This involves installing the 10uF electrolytic capacitors (be mindful of the orientation guidance provided in the manual!), the serial header, a transistor, and one more .1 uF capacitor.
Image

The reset tac switches, and three capacitors which are part of the timer reset circuit are installed now. There are two tac switch buttons; The one on the left (near the reset 555 timer) is for the CPU. The one on the right resets the propeller chip, which is an amazing 8-core microcontroller in its own right- on the PE6502 it handles all display output and keyboard input duties.
Image

The crystals are installed next. You have an option here: the main CPU oscillator can be either installed directly into the circuit board, or, with the included special oscillator socket (it's the size of a 16-pin DIP socket, but only has pins at each corner) you can solder in the socket, and then plug the oscillator of your choice into the socket. Obviously, 1MHz is guaranteed to work- and I've personally tested up to 4 MHz without any issues noticed (your mileage may vary!) The 1 MHz oscillator is included. Also, the 5 MHz crystal is installed for the propeller chip.
Image

Almost done now! Just one more step involving solder: Install the expansion header, and the propeller plug.
Image

Ok. Now, all that is left are 3 easy steps:
1) Carefully inspect the solder side of the PE6502 computer, to ensure no solder bridges are present, and that all joints are properly soldered/all parts are installed.
2) Thoroughly clean the solder side of the PE6502 with rubbing alcohol and q-tips/paper towels, or maybe even rubbing alcohol with an old toothbrush and then dry with paper towels to remove all rosin splatters from the board.
3) Carefully install the chips (you may have to bend the legs carefully to ensure they all align with the sockets- and slowly push the chips into their sockets so they seat without bending any pins!) Also note: your kit will most likely come with a 65C21 PIA instead of the 6821 PIA. Both work equally well.

The 27C256 PROM will have been programmed for you in advance. The Propeller EEPROM will also be programmed in advance. Both the serial interface or using a propeller plug (not included) with the propeller header can flash an update into the propeller.

Congratulations! You're ready to use your new computer!
-=-=-=-=-=-=-=-=-=-
Jason Putnam
putnamelectronics
-=-=-=-=-=-=-=-=-=-
Corneleous
 
Posts: 29
Joined: Sat Sep 30, 2017 4:53 pm
Location: East Coast, USA

Re: Assembly pics..

Postby ronsherr » Thu Oct 05, 2017 3:22 pm

This looks terrific!
I'm really excited about this board.
I have built a breadboard version of one of Grant's designs, but your kit looks to be totally awesome and I can't wait to buy one from you!
Great work so far!
ronsherr
 
Posts: 4
Joined: Thu Oct 05, 2017 3:14 pm

Re: Assembly pics..

Postby Corneleous » Thu Oct 05, 2017 3:28 pm

Hey- thank you very much!!!

This has been a most fun project, and I have high hopes for this computer.

I'm currently awaiting a shipment of pcboards coming in hopefully tomorrow. Components are on the way too.. So, I will announce here when kits are in stock (hopefully within 1 week) and at that time let me know if you'd like to order :-)

And, welcome to the board!
Jason
-=-=-=-=-=-=-=-=-=-
Jason Putnam
putnamelectronics
-=-=-=-=-=-=-=-=-=-
Corneleous
 
Posts: 29
Joined: Sat Sep 30, 2017 4:53 pm
Location: East Coast, USA

Re: Assembly pics..

Postby ronsherr » Thu Oct 05, 2017 3:34 pm

I'm ordering one without ANY doubt.
Unfortunately, I am going to have to start saving today, and it might take me several weeks to come up with the money...wife keeps me on a tight budget.
But I'm definitely going to buy one...I know that promise doesn't do you much good...but I will be backing it up with an official order as soon as possible! :)
ronsherr
 
Posts: 4
Joined: Thu Oct 05, 2017 3:14 pm

Re: Assembly pics..

Postby Corneleous » Thu Oct 05, 2017 7:21 pm

ronsherr wrote:I'm ordering one without ANY doubt.
Unfortunately, I am going to have to start saving today, and it might take me several weeks to come up with the money...wife keeps me on a tight budget.
But I'm definitely going to buy one...I know that promise doesn't do you much good...but I will be backing it up with an official order as soon as possible! :)


Believe me- I understand tight budgets! :-) Save as long as you want, we'll have a kit for you when you're ready!
-=-=-=-=-=-=-=-=-=-
Jason Putnam
putnamelectronics
-=-=-=-=-=-=-=-=-=-
Corneleous
 
Posts: 29
Joined: Sat Sep 30, 2017 4:53 pm
Location: East Coast, USA

Re: Assembly pics..

Postby ronsherr » Thu Nov 02, 2017 3:57 pm

we'll have a kit for you when you're ready!


Almost there...more than half saved :D
ronsherr
 
Posts: 4
Joined: Thu Oct 05, 2017 3:14 pm


Return to PE6502 Single Board Computer - Assembly and Troubleshooting

Who is online

Users browsing this forum: No registered users and 1 guest